How To Install Plasterboard On Brick Wall

1. Dwelling house
2. DIY

How to put up a plasterboard wall

An easy way to modify the feel of your room! - past

Exposed-brick walls are then sixties and seventies. Cover them with plasterboard to totally transform the experience of your room.

Hither's how

Assemble your supplies

• 10mm plasterboard sheets (quantity to suit)
• Masonry adhesive
• Cornice to friction match existing

Y'all'll as well need

Utility knife; 50 and 100mm broadknife; erstwhile chisel; drill and bits; mixing paddle; straightedge or level; cornice mitre box; chalk line; handsaw; wallboard saw; cornice cement; plasterer'south trowel; plasterer's tool; base coat; paper jointing tape; finishing compound; internal corner tool; sanding float; dust mask; 150-grit sandpaper; construction adhesive; 30mm nails.

Ameliorate Homes and Gardens

Improve Homes and Gardens

Step 1

Advisedly remove skirtings from wall and side by side walls and set aside. Run utility knife along the cornice where information technology joins ceiling and wall to cut onetime paint. Using 100mm broadknife and a hammer, loosen cornice and remove. Knock off any remaining cornice cement with old chisel so wall and ceiling are smooth. Have an electrician disconnect switches and power points, if any.

Better Homes and Gardens

Step 2

Remove other fittings from the wall, if any. Here, at that place was a balustrade butted into the wall, so we cut through the handrail 20mm from the wall postal service. This is the thickness of plasterboard and adhesive, and how much shorter the balustrade volition exist with the new wall linings.

Attaching the sheets

Stride 3

Measure length of wall at bottom and middle. Transfer measurements to one plasterboard sheet and describe a cutting line on its face up. Cut canvas past scoring along cut line with utility pocketknife. Bend sheet until it snaps, then run pocketknife along other side of sheet to consummate cut. If you crave 2 sheets to cover a wall, as we did here, employ 1 full sail, then cut second canvass to fit residue of wall. Brand cutting end become into corner of wall. To keep sheets 10mm off flooring, put offcuts on flooring next to wall. Check fit of sheets on wall prior to mixing adhesive.

Ameliorate Homes and Gardens

Footstep 4

Using drill fitted with mixing paddle, mix masonry adhesive into a thick paste. Use to wall in blobs virtually 15mm thick. Space them every 230mm at sheet ends and 450mm along and up the wall. Keep adhesive 50mm away from canvass edges.

Amend Homes and Gardens

Pace five

Bring in first sheet and press against wall. Utilize long straightedge to ensure canvas is plumb and face is apartment. Repeat for second sheet on lower half of wall, if using. Ensure tops of sheets are affluent. Press long straightedge across join to ensure faces of sheets are aligned.

Step 6

Mensurate length of wall at top and from sheets up to ceiling. Transfer measurements and cut sheets to suit, assuasive for a 20mm gap to the ceiling. Aim to stagger the canvass joins. Notch corner of sheet to fit effectually existing cornices, if necessary. Check fit on wall before mixing a new batch of adhesive.

Better Homes and Gardens

Step 7

Repeat procedure of mixing and applying adhesive to wall for superlative sheets. Elevator sheets up next to wall and press them against it. Ensure y'all do not slide sheets along adhesive blobs when applying. Use long straightedge to make sure top sheets are aligned with bottom sheets and with each other.

Installing a cornice

Stride viii

As cut angles on cornice can be tricky, information technology helps to create cut templates. Take a 400mm length of cornice and place it in cornice mitre box, which is especially designed for cutting cornice. Using an old handsaw, cutting at a 45° bending. Have another short slice and cut it the other mode. Hold pieces together every bit they would sit on the wall to form an internal corner (or external corner, if required). You may demand a few tries to get information technology correct.

Step ix

In order for the new cornice to join correctly, the existing cornice will need to exist trimmed appropriately. Identify respective cornice template on the new wall then it butts into existing cornice. Marker line of the cornice on existing i. Use wallboard saw to trim existing cornice on this line. Try fitting template into corner and keep trimming until it fits hands. Stretch chalk line betwixt undersides of existing cornice on adjacent walls and flick to create a guide for new cornice.

Stride 10

Measure betwixt adjacent walls to go length of cornice. Deduct 3mm to allow for easy plumbing fixtures. Employ cornice templates equally a guide to go angled cuts on ends right. Cut cornice.

Better Homes and Gardens

Footstep xi

Mix cornice cement with water into a thick paste. It sets chop-chop, then only mix plenty to practise 1 length of cornice. Load cornice cement on ane edge of plasterer's trowel and run trowel along both edges of cornice, leaving a 15-20mm bead of cement. Also put a little at the ends where it will bring together.

Amend Homes and Gardens

Step 12

Elevator cornice into position, gently bending in the center to get corners in first. Line up the bottom with chalk line and printing into wall and so cornice cement oozes out. If it starts to sag, agree in place with temporary nails along edges. Using 50mm wide pocketknife, scrape off excess cornice cement. Apply plasterer's tool and excess cement to fill and trim corner joints. Remove temporary nails and fill holes. Terminate past wiping a damp sponge over the work to smooth the cement, and so you don't have to sand it afterwards.

Finishing touches

Better Homes and Gardens

Step 13

To set up joints between sheets, mix upwardly base of operations coat and spread along articulation. Printing paper jointing record into wet compound and piece of work your manner forth joint, removing any wrinkles or bubbles in tape. Finish with a skim coat that just covers record. Internal corners are set the same way. Fold paper jointing tape forth crease in centre and utilise internal corner tool to press record into base coat. Exit to set, then apply a 2nd, wider skim coat to joints and corners, feathering edges to plasterboard. Get out to gear up.

Step 14

Use a coat of finishing compound 300mm wide to joints, feathering edges to sheets. On butt joint where ends of sheets meet, make chemical compound 600mm wide to properly alloy joint. Use internal corner tool to apply finishing compound to corners. Allow to dry for at least 24 hours.

Meliorate Homes and Gardens

Step xv

Wearing dust mask, carefully sand with 150-grit sandpaper. Check for smoothness by running your hands along the join, feeling for any ridges. Remove all dust, then paint with a sealer undercoat followed by a topcoat in your selected colour. Allow to dry, and then apply a 2nd coat.

Better Homes and Gardens

Footstep 16

Employ construction agglutinative to dorsum of skirtings and put on wall. Use 30mm nails to concord skirting to sheets while glue dries. Cutting skirtings on adjacent walls to suit new walls. Supervene upon any other fittings, such as the balustrade post here, and blast in. Have an electrician reconnect power points and switches, if required.

You lot may also like

How to install skirting boards

How to transform a brick wall

Source: https://www.bhg.com.au/how-to-put-up-a-plasterboard-wall

Posted by: milleransuchan.blogspot.com

Share this post